ADAPTERS

This PYREX 105° angle vacuum connecting adapters have an outer 24/40 Standard Taper joint at the top and an inner-sealed through drip-tip joint at the bottom. Bent at a 105° angle. The serrated sidearm has a 10 mm OD. Drip-tip at the bottom...

With tubulation of 10 mm OD for attaching to a vacuum pump or to inner and outer TS joints. Includes a drip-tip on the inner tub.Image(s) are representative of the product group and not necessarily the individual product.Standard Taper Bottom Inner...

The arms are approximately 105 DEG apart. One end is equipped with an outer TS 24/40 joint and the other end with an inner TS 24/40 joint of the same size. Used as a receiver adapter.Image(s) are representative of the product group and not necessarily...

These adapters are fabricated with heavy walls for mechanical strength and are further strengthened by the heavy, uniform rim at the top which affords a serviceable finger grip.These adapters are shorter than the conventional type, thus allowing more...

With full-length inner TS 24/40 joints of same size. The connecting arm is approximately at a 75 DEG angle from vertical and is 200 mm long.Image(s) are representative of the product group and not necessarily the individual product.

The sidearm is at an angle approximately 75 DEG from the lower part of the vertical tube. The joint on the sidearm is at an angle approximately 105 DEG from the sidearm. The sidearm and lower tube are equipped with inner TS joints of the same size. The...

With an outer TS joint at the top and a smaller inner TS joint at the bottom.Image(s) are representative of the product group and not necessarily the individual product.TS Joint Size Top Outer: 24/40TS Joint Size Bottom Inner: 19/38Approx. Length (mm):...

Made with inner angle of 105°. Upper end is equipped with outer TS 24/40 joint. Lower end cut off at angle for use as a receiver adapter. Tube OD 12 mm.Image(s) are representative of the product group and not necessarily the individual product.

Two way tube with arms at 105° angle. Both arms have TS 24/40 joints. Approximate stem length below joint, 170 mm. Vacuum tube O.D., 10 mm.Image(s) are representative of the product group and not necessarily the individual product.

The sidearm on this PYREX tube adapter is at an angle approximately 75° from the lower joint. The lower end and sidearm are equipped with 2 inner Standard Taper 24/40 joints. The Standard Taper 10/30 outer joint accommodates a thermometer.Image(s)...

The arms are approximately 75 DEG apart and are equipped with inner TS 24/40 joints at both ends. Often used as a stillhead adapter.Image(s) are representative of the product group and not necessarily the individual product.

The manometer tube is enclosed in a round bottom, graduated jacket and is sealed to a stopcock plug. In use mercury is placed in the inner tube and in the jacket bottom to measure the pressure differential. Not recommended for positive pressure. The...

Provides on/off control with the main valve. Allows delivery of preset volumes of gases or liquids to reactions using the needle valve.Image(s) are representative of the product group and not necessarily the individual product.

Vertical adapter with vacuum take-off and drip tip.Image(s) are representative of the product group and not necessarily the individual product.

For regulating the input of gases or liquids into reaction systems.• Stopcock has a glass plug• Inner Standard Taper joint on one end and a 90 DEG hose connection on the opposite end• Manufactured from 33 expansion, low extractable...

Hose inlet 90 degree adapters. Ideal for use as a vent or for the introduction of pressure/vacuum. Inner Standard Taper joint at the bottom and hose connection on the side. Manufactured from 33 expansion, low extractable borosilicate glass conforming to...

Designed with two side hose connectors for venting or introducing gas/vacuum into a system. Hose connections fit 3/8 in. I.D. flexible tubing. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type...

For the introduction of gases or liquids during reactions. Hose connection fits 1/4 in. I.D. flexible tubing. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements.Image(s)...

For the introduction of gases or liquids to reactions. Fits 10 mL round bottom flasks with a 10/18 joint. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements.Image(s) are...

Used to introduce reactants below the liquid surface. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirements.Image(s) are representative of the product group and not...

Compact adapter with a Standard Taper 10/30 upper joint which can be used with a jointed thermometer or 179800 universal adapter for thermometers (see accessories), gas inlet tubes, etc. Side hose connection for gas/vacuum introduction and venting...

Placed above a boiling flask to prevent foaming-type reactions from entering either the distilling column or the condenser. Useful with rotary evaporators. Cat. No. 985-25489 features a more extensive baffle system than other traps. Manufactured from 33...

Bushing adapters allow for compact assemblies of dissimilar joints. 10/30 sizes on small (top) joints are useful as fittings for thermometers. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type...

This adapter assembly is designed to allow connection of a 47 mm or 90 mm filtration support base with a straight drip tip to a bottle or reservoir with a GL 45 thread. • Filtrate is collected directly into a media-type bottle when using a standard...

Size 15 o-ring connector (15 mm I.D.) for use with HI-VAC® manifolds (Cat. No. 985-14308, 985-143017, 985-14320, and 985-14323) and 179920 adapters (see accessories). Manufactured from 33 expansion, low extractable borosilicate glass conforming to...

Ideal for use as a vent or for the introduction of pressure/vacuum. Standard Taper joint at one end and vertical hose connection at the other. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type...

Used for precise pouring of liquids from reactors and joint flasks. Designed to eliminate droplet run-back. Suitable for dry box and remote applications. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM...

For regulating the input of gases or liquids into reaction systems. Stopcock has a glass plug (replacement available, Cat. No. 985-40117). Outer Standard Taper joint on one end and 90° hose connection on the opposite end. Manufactured from 33...

For regulating the input of gases or liquids into reaction systems. Stopcock has an PTFE plug (replacement available, Cat. No. 985-41623). Inner Standard Taper joint on one end and a 90° hose connection on the opposite end. Manufactured from 33...

Hose connection on the side accepts 3//8 in. I.D. flexible tubing. Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirementsImage(s) are representative of the product group and...

Standard Taper joint at the bottom and a tubulature at the top. Includes a rubber adapter with a 1/4 in. hole in the top for use with plain stem thermometers, gas inlet tubes, etc. (replacement rubber adapters available, Cat. No. 985-38500). Side hose...

Expands length of apparatus and is also useful as an air condenser. 985-16039, 985-16042 and 985-12031, 985-12034 adapters have outer Standard Taper joints at one end and inner Standard Taper joints on the other end985-12049 and 985-12055 adapters have...

O-ring socket joint hose connectors. Standard Spherical Joint sizes fit existing apparatus using spherical joints and permit attachment of flexible hose without costly modification of the apparatus. Manufactured from 33 expansion, low extractable...

For reducing the size of Standard Taper glass joints.• Outer joint is at the top, inner at the bottom • Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A...

• Standard Taper outer joint at top• Tapered drip tube extends into open receivers • Manufactured from 33 expansion, low extractable borosilicate glass conforming to USP Type I and ASTM E438, Type I, Class A requirementsImage(s) are...

Connects to vacuum systems, NMR tubes, photochemical cuvettes, lyophilizing tubes, flowmeters, etc. Simple O-ring connections form a vacuum seal on glass tubing by tightening the compression capSupplied with FKM o-ring and open top polypropylene capBody...

• Provides dual entry into a variety of flasks• Compatible with glass BEVEL-SEAL inlet adapters or PTFE BEVEL-SEAL inlet adapters for thermometer use at either top opening• Useful for reflux with addition-type reactions• Joints...

For use with multiple entry flasks or reaction vessels. Design helps avoid possible contact with stirrer shafts.Image(s) are representative of the product group and not necessarily the individual product.

Used for connecting glass tubing.All connectors have an overall length of approximately 50 mmOpen top cap is suitable for use to 150°CBlue glass-filled nylon capO-rings are FKMManufactured from 33 expansion, low extractable borosilicate glass...

Polypropylene Replacement Caps for Connecting Adapters:• 985-12937: 5/8 in. - 18, Fits OD 8 mm, Hole Dia. 8.5 mm• 985-12940: 3/4 in. - 16, Fits OD 10 mm, Hole Dia. 10.5 mmImage(s) are representative of the product group and not necessarily...